Page 7 of 9 FirstFirst ... 56789 LastLast
Results 61 to 70 of 83

Thread: HZ panelvan resto

  1. #61
    So kept pushing on... The next job was getting it all in hi build primer and guide coat - the realise just how many high and low spots there still were!!!

    Guide coat 1.jpg

    Guide coat 2.jpg

    Guide coat 5.jpg

    And baking in the sun...

    Guide coat 4.jpg

    Now to rub back, find the highs and lows, fix them and then start to prep for paint...

  2. #62
    Night Rider Valencia's Avatar
    Join Date
    Jul 2011
    Location
    Perth
    Posts
    4,095
    Doing well Duncan

  3. #63
    Guide coat getting rubbed back... kind of happy with the job so far - only a few areas for corrections that I've found so far...

    Guide coat rub back 1.jpg

  4. #64
    So with the guide coat mostly rubbed back, and dust and crap getting everywhere, I decided to also strip the rear of the van as well... Anyone who has done this job will point out just how horrible it is... I mainly used wire wheels, strip discs and paint stripper. If you do this be careful not to go too heavy on the floor as it is zinc coated and you don't want to strip that off...

    Stripping rear 1.jpg

    Stripping rear 2.jpg

    When the sides were done I got into the floor...

    Stripping rear 3.jpg

    Then put it all in etch primer...

    Stripping rear 4.jpg

    Stripping rear 5.jpg

    Stripping rear 6.jpg

    So this little job took the the better part of 3 or 4 days!! Still got a couple of little rust holes in the wheel arches to do at this stage as well as a bit of finessing with the sides that were welded in, but overall not too bad. I won't go over the top with the rear area as I fully plan on decking it out once the car is completed, but I still want it to look pretty good until then.

  5. #65
    Night Rider Innuendo's Avatar
    Join Date
    Aug 2012
    Posts
    3,448
    Nice job cleaning out the rear. Lots of work but it's paid off for you.
    Selling HJ 253 Engine
    Engine Number QR718*** | 19M5 Clock Casting at 6 O'Clock
    19th December 1975 Suit HJ Late Dec 1975 to April 1976

  6. #66
    Thanks mate. Yeah I haven't been too anal retentive about it but I have got it reasonably straight... enough to look OK until I deck the rear out anyway....

    So re-did the seam sealer that I'd stripped away... Again, wasn't trying to make it pretty... the factory didn't anyway...

    Seam sealing 1.jpg

    Seam sealing 2.jpg

    Seam sealing 3.jpg

  7. #67
    The next job was getting the front spoiler rubbed back and in primer

    Spoiler .jpg

    Spoiler 1.jpg

    Spoiler 2.jpg

    I also set up the console brackets and welded them in place as well...

    Console brackets 1.jpg

    So back into the panels and body shell

  8. #68
    Night Rider Innuendo's Avatar
    Join Date
    Aug 2012
    Posts
    3,448
    You changing the bench seat shifter stick for use with the console?
    Selling HJ 253 Engine
    Engine Number QR718*** | 19M5 Clock Casting at 6 O'Clock
    19th December 1975 Suit HJ Late Dec 1975 to April 1976

  9. #69
    Yep - got a normal shifter here.

    Checked the operation of both shifters to ensure no fouling before I welded the brackets in

  10. #70
    OK - so onto the rust repairs in the rear cargo area....

    Firstly there were only two at the base of each wheel arch... Cut them out...

    WElding 2.jpg

    Then cut a piece to fit and weld in... (this is the other side - it was at the front of the wheel arch)

    Welding 1.jpg

    And primed and ready for some minor filler and then paint...

    WElding 3.jpg

    And then moving on. Look, I know as restos of panelvans go this is a simple one. But it still takes forever....
    Last edited by DuncanM; 28-02-2024 at 03:33 PM.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •