Results 1 to 5 of 5

Thread: What is a twin headlight radiator support worth.

  1. #1
    Cruiser axistr's Avatar
    Join Date
    May 2017
    Location
    Windsor NSW
    Posts
    280

    What is a twin headlight radiator support worth.

    I have decided to clear out most of my parts collection. I have a twin headlight radiator support panel but not sure how much to put on it. It has no rust whatsoever, never had any repairs or damage. Still has original rust poofing on it. Straight as, to the point that its like new old stock.

    OK so what is the going price these days.? Next question.
    I believe this one is from a HZ. Is there any difference between all the models, and what is the difference between the HQ.?

    Other parts :

    Hayman Reece heavy duty tow bar complete , HQ-WB
    Front and rear bumper bar brackets. HJ-HZ
    WB V8 radiator.
    HJ front guard weld in flutes.
    Heaps of small parts to many to mention.
    Left and right HQ-WB front doors. With hard ware.
    Door hinges. (front)
    Weld in front floor panel right side.

    Small block chevy parts, Edelbrock performer RPM Inlet manifold, Holley 780cfm vacuum secondary carby. Mallory electronic distributor. All the above chev parts have done less than 2,000 km. Only remove due to going EFI.

    Many Torana parts but will list them on the Torana forum.

    PM me if you have any questions.

    Cheers Lenny.

  2. #2
    It's a rockin' Sandaro's Avatar
    Join Date
    Jul 2011
    Location
    Picton NSW
    Posts
    1,128
    I believe there is a difference hq to later hj-z but I don't know what? Is your question a pop quiz? Or you don't know either?

  3. #3
    Night Rider Valencia's Avatar
    Join Date
    Jul 2011
    Location
    Perth
    Posts
    4,095
    Seen those radiator support panels go for $250 to $450
    to me if its as good as you say $400 would be a fair price me thinks
    but some people would rather buy a shitty one and give a panel beater $500 to fix it go figure
    Pm Sent

  4. #4
    Cruiser axistr's Avatar
    Join Date
    May 2017
    Location
    Windsor NSW
    Posts
    280
    DSC_0289.JPGDSC_0292.JPG

    Ok identified the radiator support it HJ-HZ. Thanks Maxsandman.

    I have also come across some bonnet hinges. They are new chromed and haven't been fitted. I wrapped them in tape some time ago so the chrome wouldn't get scratched or damaged. The two holes in the hinges that bolt to the inner guards are not slotted like the LH-UC or HQ-WB I could be wrong but if memory serves me right they suit HK-HG I will let the experts guide me on this one. And of course a ball park of what they might be worth.

    DSC_0315.JPG

    Thanks in advance,

    Lenny.
    Last edited by axistr; 06-08-2020 at 05:16 PM.

  5. #5
    Sandman Driver maxsandman's Avatar
    Join Date
    Aug 2014
    Location
    country N.S.W.
    Posts
    624
    Yes, HK-T-G bonnet hinges basically same as later models, but bolt holes to the guards arn't slotted.
    I had same chromed hinges on my HZ van years ago, & after a bit if mucking around, the bonnet sat OK.
    Cheers
    Max

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •