Page 3 of 8 FirstFirst 12345 ... LastLast
Results 21 to 30 of 73

Thread: Big Rob's HZ Ute Shop Truck....

  1. #21
    Cruiser jason.ruff's Avatar
    Join Date
    Jun 2012
    Location
    Darwin
    Posts
    416
    Check the hose and vacuum modulator as well.

  2. #22
    It's a rockin' Big Rob's Avatar
    Join Date
    Aug 2013
    Location
    Eurobodalla NSW South Coast
    Posts
    1,829
    Thanks... I've checked and I reckon the vacuum is intact, certainly at the inlet manifold. I guess I need to check where it enters the box.

    I drove it to the golf course (only about 5km each way) this afternoon and it behaved pretty well. I'll give it a longer run tomorrow and see what happens.

    I don't think it can be a dud trans when it goes so hard in 1st and second but autos aren't my area of expertise so any advice is cool.
    Vans.... This is the 2nd time round the block, 40 years later! talk about turning back the clock!

  3. #23
    Just sounds like a 6 cylinder sludge matic

  4. #24
    It's a rockin' Big Rob's Avatar
    Join Date
    Aug 2013
    Location
    Eurobodalla NSW South Coast
    Posts
    1,829
    20170701_154042.jpg20170701_154053.jpg20170701_154058.jpgDrove it to Saturdays club run and it was fine...
    Gave it a cut and polish afterwards....
    Vans.... This is the 2nd time round the block, 40 years later! talk about turning back the clock!

  5. #25
    Cruiser jason.ruff's Avatar
    Join Date
    Jun 2012
    Location
    Darwin
    Posts
    416
    Looks good for a parts runner. Little bit of love makes a big difference.

  6. #26
    Sandman Driver davegmh's Avatar
    Join Date
    Feb 2014
    Location
    Toowoomba
    Posts
    710
    Looks pretty cool now Rob.
    Disclaimer: I am not an expert.

  7. #27
    Night Rider Valencia's Avatar
    Join Date
    Jul 2011
    Location
    Perth
    Posts
    4,095
    40 years on still delivering the goods

  8. #28
    It's a rockin' Big Rob's Avatar
    Join Date
    Aug 2013
    Location
    Eurobodalla NSW South Coast
    Posts
    1,829
    Thanks guys.... It sure has scrubbed up well.
    I cleaned out the plenum yesterday.... I've never seen so many leaves and crap in a plenum before and not a spot of rust!
    It does however let a tiny bit of water in the left side... it's coming from up high but because of all the aircon stuff behind the glovebox I can't see where. Drain is clear so I guess it might be the air flap not sealing properly.
    Vans.... This is the 2nd time round the block, 40 years later! talk about turning back the clock!

  9. #29
    I had one leak with a crack in the drain pipe

  10. #30
    It's a rockin' Big Rob's Avatar
    Join Date
    Aug 2013
    Location
    Eurobodalla NSW South Coast
    Posts
    1,829
    Ahhhhh.... it could be that!
    I think I'll bite the bullet and pull all the aircon stuff out from behind the glovebox... I can just reach up and feel the drain pipe and it does feel like its a bit crushed so could have a crack...
    Pain in the neck, but it has to be fixed.
    Vans.... This is the 2nd time round the block, 40 years later! talk about turning back the clock!

Thread Information

Users Browsing this Thread

There are currently 5 users browsing this thread. (0 members and 5 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •