Results 1 to 9 of 9

Thread: Which Diff to upgrade to?

  1. #1
    P Plater HXsman's Avatar
    Join Date
    Jul 2016
    Location
    Melbourne
    Posts
    96

    Which Diff to upgrade to?

    Hi all,

    I am currently replacing my tired 253 with a 355. Everyone suggests I might need to worry about my diff. Its currently a GU4 (3.04?) behind a Trumatic.

    What should I upgrade to other than a ridiculously expensive 9"

    I'm not looking to race / drag or burnout (too old for that)

    Just need to be sure it can withstand the 355

    Appreciate your thoughts

  2. #2
    Banned
    Join Date
    Feb 2010
    Location
    Central West NSW
    Posts
    4,463
    Just stick with the Salisbury. If you drive to its limits you will get some miles out of it. They raced at Bathurst in an A9X with one. The alternative that's common is 9 inch.

  3. #3
    It's a rockin' Sandaro's Avatar
    Join Date
    Jul 2011
    Location
    Picton NSW
    Posts
    1,128
    No burnouts, then no problem requiring an upgrade

  4. #4
    Night Rider Valencia's Avatar
    Join Date
    Jul 2011
    Location
    Perth
    Posts
    4,095
    Quote Originally Posted by Sandaro View Post
    No burnouts, then no problem requiring an upgrade
    Agree your diff is a 3.08

  5. #5
    How much is a 9 inch these days ?
    If you put 3.00 or 3.25 9 inch in you would never look at it again

  6. #6
    Night Rider Valencia's Avatar
    Join Date
    Jul 2011
    Location
    Perth
    Posts
    4,095
    Quote Originally Posted by Beachy View Post
    How much is a 9 inch these days ?
    If you put 3.00 or 3.25 9 inch in you would never look at it again
    My 9 inch LSD 3.1 was installed in 1990 havnt even changed the oil ever
    one thing i do know they are stronger than the keyway on a 308

  7. #7
    Cruiser
    Join Date
    Sep 2013
    Location
    Eastwood, NSW
    Posts
    366
    The 9-inch Ford diff is not that strong in stock form. OK, it's tougher than a 10-bolt Holden Large Salisbury, but it's not the be-all & end-all.

    My B06 One-Tonner with 308 TH400, even in standard form was a bit hard on diffs back in the 80s. Yes, it was driven hard & did a lot of towing, but didn't do any burnouts. I killed 3 standard diffs, then changed to a 3.25 9-inch.

    The side carrier bearings went noisy within 1 year & then the pinion seal began leaking badly, the diff guy said that this was commonplace, so I spent big $$$ having it overhauled.

    Less than 18-months later it began making very strange noises so it out it came again. The 'hat' part of the centre carrier had cracked & separated, right around the outside thru the centreline of the crown wheel retaining bolts. Again this was a "common" failure so I had it upgraded with a aftermarket billet hat, the original was just cast iron. I do less mileage in it these days & it has held together. By the way, the original 28-spline axles are still in there today. The conversion involved using Holden axles & brakes with the Ford centre.

    When we were drag racing, the 9-inch was the thing to have, but again all 9-inch diffs are not equal. In our Monaro we went thru 28-spline thin axles, 28-spline thick axles, 31-spline GT-HO axles, & then finally 35-spline aftermarket items (Mark Williams) & a billet one-piece spool to replace the standard LSD centre, before we stopped picking up broken diff pieces & spending money over & over again. This was a 10-sec sedan SS/A car, not far removed from a street car, it wasn't a Pro-Stocker or Door-Slammer.

    Good alternatives for use in a Sandman would be an M75, M78 or M80 out of a late Holden or Falcon. More commonplace & cheaper than an overhauled 9-inch Ford unit.

    Another conversion I've seen is the fitting of B-W gears & hemisphere to a standard Holden Salisbury housing. It is stronger than the original & the parts are plentiful, as some of the 10-bolt bits are getting scarce. It also looks concours original from the outside.

    Dr Terry
    Last edited by Dr Terry; 14-06-2017 at 08:07 AM.

  8. #8
    im getting some prices on putting a truetrack lsd centre into my 3.08 salisbury complete job with new bearings appox $1650 to$1850

  9. #9
    P Plater HXsman's Avatar
    Join Date
    Jul 2016
    Location
    Melbourne
    Posts
    96
    Thanks all,

    I agree with the general assessment. Don't do burnouts and if it blows one day then worry about it !

    Appreciate all your input

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •