Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Extractors to suit HJ manual with EFI

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Cruiser razsandman's Avatar
    Join Date
    Jul 2010
    Location
    Adelaide
    Posts
    275

    Extractors to suit HJ manual with EFI

    Hi all.
    I have my HJ running efi 5.0 with aussie 4 speed with the original rat trap clutch mechanism. I want a decent set of extractors. Anyone have that combination. I cant find an off the shelf set that fit with that style of clutch.
    1976 HJ XX7 Sandman
    Genuine VN SS manual atlas grey
    HX LE Coupe project

  2. #2
    Sandman Guru
    Join Date
    Jul 2010
    Posts
    6,451
    You won't find any, probably as most people doing this conversion keep the 4L60/4L60E auto or use the T5 that came with the engine which means cable normally full cable clutch.

  3. #3
    Sandman Driver hainzy's Avatar
    Join Date
    Apr 2010
    Location
    BALLARAT
    Posts
    699
    Yeah Im looking at doing this down the track. I certainly wont be leaving the rat trap setup in there. Everytime I push the clutch in it strains and creaks and Im waiting for it to snap! On the plus side though Ive probably got a muscley left leg! Going cable is one of the pluses! Ill be leaving my supra 5 speed in and hope Ill be able to sort out some extractors.

  4. #4
    Cruiser razsandman's Avatar
    Join Date
    Jul 2010
    Location
    Adelaide
    Posts
    275
    For Hainzy - I had the VN 5.0 with supra 5 and the aussi 4 fitted with the factory VQ statesman style extractors. you just need to plug the o2 sensor hole because the sensor doesn't fit in that spot, weld another sensor mount on a different angle. then had a new system built from there back. I'll possibly be selling my complete old system if I can sort out a new system.
    1976 HJ XX7 Sandman
    Genuine VN SS manual atlas grey
    HX LE Coupe project

  5. #5
    Cruiser razsandman's Avatar
    Join Date
    Jul 2010
    Location
    Adelaide
    Posts
    275
    so ended up deciding to get the Dellows Hydraulic clutch conversion so I can fit the big pipes in
    loudness coming my way
    1976 HJ XX7 Sandman
    Genuine VN SS manual atlas grey
    HX LE Coupe project

  6. #6
    Cruiser razsandman's Avatar
    Join Date
    Jul 2010
    Location
    Adelaide
    Posts
    275
    Fair enough, I had 6 supra 5 speed gearboxes in my van behind this engine... I now have a pile of 6 broken supra 5 speeds.. the toughened aussi 4 speed has way out lasted all the jap crap boxes and I have a speedo that works again Castle Headers advertise a set that's meant to fit and they assured me they will fit but I tried and the don't!

    I am considering doing a hydraulic clutch conversion over a cable. Dellows make a good kit. little more expensive than the Castle main rod shop kit but from experience the CRS kit was crap.

    My experience with cable vs Mechanical I've owned a few of each and the early commodores and actually like the mechanical. if its in good condition with no sloppy pins, good rubber bush at the top and adjusted spot on they work beautifully and light under foot. I'm running a super heavy duty clutch in the van and a standard heavy duty in the VN SS and the van is way lighter and better to operate. this is why I was trying to find a good set of extractors to fit. I was trying to find an off the shelf set to save time. (one of the reasons I found the CRS clutch kit and bell housing for the supra box crap was because you cant adjust it correctly but thats another story altogether)
    Last edited by razsandman; 18-06-2015 at 03:35 PM.
    1976 HJ XX7 Sandman
    Genuine VN SS manual atlas grey
    HX LE Coupe project

  7. #7
    A toughened aussie 4 speed must be a big improvement on a standard one they were crap

  8. #8
    Cruiser jason.ruff's Avatar
    Join Date
    Jun 2012
    Location
    Darwin
    Posts
    416
    For speedway we used to machine out where the needle rollers ran and fit brass bushes. Tough as, removed one of the major weak spots of these boxes.

  9. #9
    Was that in the cluster shaft its Over 20 years since I pulled one apart I reckon there would be five broken aussie boxes in the back of the shed

  10. #10
    Cruiser jason.ruff's Avatar
    Join Date
    Jun 2012
    Location
    Darwin
    Posts
    416
    Mainly the lay shaft I think, having a bit of CRAFT at the moment. May have been in the clusters as well, anywhere there were needle rollers.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 253 Extractors?
    By hilta in forum Engine
    Replies: 10
    Last Post: 19-07-2015, 04:02 PM
  2. Replies: 4
    Last Post: 08-02-2014, 07:07 AM
  3. HQ-WB V8 Extractors
    By hxbunny in forum My Items For Sale or Buy
    Replies: 9
    Last Post: 23-04-2013, 06:16 PM
  4. Extractors
    By Valencia in forum The Lounge
    Replies: 16
    Last Post: 23-03-2013, 04:12 AM
  5. Extractors
    By HK1837 in forum Archive
    Replies: 0
    Last Post: 04-03-2012, 07:28 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •