Page 2 of 2 FirstFirst 12
Results 11 to 17 of 17

Thread: NOS HZ RTS chassis for sedan

  1. #11
    Leadfoot
    Join Date
    Feb 2015
    Posts
    173
    Did the HZ models have problems with there chassis??? someone told me the HQ chassis was a lot stronger, any truth in that? and what is the difference on the chassis for RTS?

  2. #12
    Sandman Guru
    Join Date
    Jul 2010
    Posts
    6,451
    HZ chassis is thinner steel and aparantly better quality. HQ chassis is identical to HJ and also HX up until about 6/77. Late HX are the same as HZ.

    If you put a HQ-6/77 HX side by side with a 6/77 onwards and look at the upper control arm mount and where the shock absorber sits you'll see the difference. Shocky doesn't move relative to the rest of the chassis but its position relative to the upper control arm does. Read up on suspension geometry and what moving the upper control arm backwards does and you'll get an idea.
    Last edited by HK1837; 10-05-2015 at 07:39 AM. Reason: Error

  3. #13
    It's a rockin' mauser's Avatar
    Join Date
    Nov 2010
    Location
    Canberra, ACT
    Posts
    1,148
    Quote Originally Posted by tidyvan View Post
    Rounded.
    ... not WB.

    Mauser
    “485650 HQ's cant be wrong...”
    “You don’t drive a Kingswood, you make love to it. That’s why nuns only drive Toranas.” - Ted Bullpitt

  4. #14
    Decal Demon stickthis's Avatar
    Join Date
    Feb 2010
    Location
    SA
    Posts
    1,957
    Good score!

  5. #15
    P Plater tidyvan's Avatar
    Join Date
    Jan 2015
    Location
    Central Coast, NSW
    Posts
    75

    Reviving this old thread - why the difference?

    The attached picture shows a van chassis (left) and a sedan chassis (right). The van chassis arms are fully closed while the sedan chassis arms are open C shapes, but with a box section (second hole from the top) on them.
    The diagram has a circle where I expected the front chassis would join the rear chassis.
    If the front part of the chassis is replaced, does that mean the inside closed part of the van chassis, nearly the full length of the arm, has to be picked off and then attached to the new front part?

    Pic
    TwoChassis.jpeg

    Diagram
    ChassisJoin.jpeg
    We'll get there shortly.

  6. #16
    Banned
    Join Date
    Feb 2010
    Location
    Central West NSW
    Posts
    4,463
    You can see it slips up inside the rear commercial chassis. Yes I would think it would go all the way up there as it would be weak as anything if it didn’t.
    Be easier just to find a better commercial chassis.

  7. #17
    Sandman Driver maxsandman's Avatar
    Join Date
    Aug 2014
    Location
    country N.S.W.
    Posts
    624
    The commercial chassis gets cut where it widens out right near the front cab mount is. You can see a vertical slot on the outside of the chassis, that is cleaned out, & the car chassis is stitched through that slot.
    I reckon there would be a repair procedure around, someone may have a copy of.
    This was a common repair on tonners in the 80s & 90s, I was involved in a few over the years. Guys bought front end damaged ones, & put them back on the road. Would buy a sedan out of the paper on the weekend, (we would usually buy prems or done up cars, so we could sell off all the bits) strip the chassis down, & take the ute/tonner to panel shop (with the cab off, & bare replacement chassis, & for a bit of cash, they would get it done after work within a couple days.
    The ute would be back on the road next week.
    Never actually saw it being done, but I'm sure the car rails were cut, & only part was tied in

    Cheers
    Max

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. HJ GTS sedan
    By HK1837 in forum Vehicles or Items Found for Sale
    Replies: 2
    Last Post: 21-03-2015, 05:56 PM
  2. HQ sedan
    By Taily in forum Vehicles or Items Found for Sale
    Replies: 1
    Last Post: 17-08-2014, 03:25 PM
  3. Hq Sedan info
    By Gunna Do in forum The Lounge
    Replies: 4
    Last Post: 02-03-2014, 12:52 AM
  4. HX Ute Chassis - Victoria & HJ PV Chassis - Sydney.
    By ABSINTH74HQ in forum My Items For Sale or Buy
    Replies: 0
    Last Post: 23-09-2013, 04:09 PM
  5. HQ sedan chassis x2
    By razsandman in forum My Items For Sale or Buy
    Replies: 2
    Last Post: 24-06-2013, 05:49 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •