Results 1 to 8 of 8

Thread: Replacing ute inner rear wheel arches

  1. #1
    P Plater AN5590's Avatar
    Join Date
    May 2010
    Location
    Adelaide
    Posts
    97

    Replacing ute inner rear wheel arches

    I want to replace the inner rear wheel arches in my HQ ute (donor body) - the body is pretty good rust wise but the inner arches look like they have been attacked with a sledge hammer, the tray itself is OK.

    How hard is it to replace them? I have scuffed the paint along the top of the arch to see where the spot welds i'm but having trouble working out what happens once they get to the tray - my Holden HQ Manuals aren't much help!

    I am assuming they are one piece that continues down below the tray into the lower wheel arch area? Was wondering if it was possible to drill out the spot welds along the top of the arch and then just cut them at the tray line - or is that really dumb idea? :confused:

    Hopefully the pic will show what I mean - unfortunately the pic is not of my ute!


    Any help much appreciated...

    P.S. I'm pretty much in the teach yourself category when it comes to bodywork.:eek:

  2. #2
    Certifiable ozbox's Avatar
    Join Date
    Mar 2010
    Location
    newcastle
    Posts
    2,385
    to find the spot welds for the bottom edge at the tray you need to take a wheell off and look in there..get wheel arch cut sections from a panelavan..i can help with those if you have troubles finding some..

  3. #3
    P Plater AN5590's Avatar
    Join Date
    May 2010
    Location
    Adelaide
    Posts
    97
    Quote Originally Posted by ozbox View Post
    to find the spot welds for the bottom edge at the tray you need to take a wheell off and look in there..get wheel arch cut sections from a panelavan..i can help with those if you have troubles finding some..
    Thanks - have only had quick look underneath with wheel on and I thought it was one panel ie: no join at the tray edge - hence my thought that I would need to cut it.

    So will go back and have a proper look underneath on the weekend, have yet to really look for replacement arches so will be in touch if I can't get anything decent local. Cheers Iain

  4. #4
    P Plater AN5590's Avatar
    Join Date
    May 2010
    Location
    Adelaide
    Posts
    97
    Quote Originally Posted by ozbox View Post
    to find the spot welds for the bottom edge at the tray you need to take a wheell off and look in there..get wheel arch cut sections from a panelavan..i can help with those if you have troubles finding some..
    Managed to get under and have a proper look today, cleaned up along the spot welds at tray join and also tray cross bar support (or what ever you call it).

    Anyway looks like a fair few spot welds and lot of stuffing around to get the full inner arch out - especially where it joins the seperate section of wheel arch that meets with the inner rear quarter panels.

    So still wondering about just taking out the top spot welds and cutting along the wheel arch at tray level and just replacing the upper sections, have tried to show what I am on about in pic's below. So good, bad, stupid idea? Any issues with welding in and sealing just the upper section? Any help appreciated. Thanks.





  5. #5
    Decal Demon stickthis's Avatar
    Join Date
    Feb 2010
    Location
    SA
    Posts
    1,957
    Whats wrong with your arches? This seems like a huge job. Are yours dented? If so they can be repaired easier than replacing them. Good thing is you can get to both sides of the steel so heating and beating will get them back to normal if you know what your doing.

    Replacing them without it looking obvious that you did will be hard.
    Owner (Jason) - STICKTHIS Automotive Decals and Stripes

    HX Sandman Panelvan. Mint Julep. Complete Factory Resto.
    HZ Sandman Ute. Saddle Tan Metallic - Customised. Galaxy Blue.
    HZ GTS. Palais White. Next Resto From 99% NOS Parts.
    HSV GTO Coupe - Highly Modified
    VR SS into a VS Supercar Castrol Perkins Ingall 1997 Tribuilte build

  6. #6
    Certifiable ozbox's Avatar
    Join Date
    Mar 2010
    Location
    newcastle
    Posts
    2,385
    unless they were absolutely crushed i would repair rather than replace..it is a big job to even cut and shut the way you want too..:eek:

  7. #7
    P Plater AN5590's Avatar
    Join Date
    May 2010
    Location
    Adelaide
    Posts
    97
    Thanks for the feedback - as per my original post the inner arches are pretty trashed. The body is pretty good rust wise - all the usual rots spots are solid but the inside tray has clearly had a hard life.

    Originally thought it might be easier to replace than try to beat out - am re-thinking that one now... Thanks again.

  8. #8
    Decal Demon stickthis's Avatar
    Join Date
    Feb 2010
    Location
    SA
    Posts
    1,957
    Quote Originally Posted by AN5590 View Post
    Thanks for the feedback - as per my original post the inner arches are pretty trashed. The body is pretty good rust wise - all the usual rots spots are solid but the inside tray has clearly had a hard life.

    Originally thought it might be easier to replace than try to beat out - am re-thinking that one now... Thanks again.
    Yeh I would beat them out if you can. even it it takes you a day each wheel arch. As thats about what it will take to replace them. And you would never get them to look original in my opinion =)
    Owner (Jason) - STICKTHIS Automotive Decals and Stripes

    HX Sandman Panelvan. Mint Julep. Complete Factory Resto.
    HZ Sandman Ute. Saddle Tan Metallic - Customised. Galaxy Blue.
    HZ GTS. Palais White. Next Resto From 99% NOS Parts.
    HSV GTO Coupe - Highly Modified
    VR SS into a VS Supercar Castrol Perkins Ingall 1997 Tribuilte build

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Rear wheel kW and Torque
    By HK1837 in forum The Lounge
    Replies: 9
    Last Post: 14-05-2015, 09:11 PM
  2. Hand brake light needs replacing
    By Kiwivan in forum Electrical
    Replies: 8
    Last Post: 25-04-2014, 04:08 PM
  3. Wheel arches...
    By Big Rob in forum Interior
    Replies: 6
    Last Post: 12-10-2013, 12:32 AM
  4. Different sized wheel arches
    By Frosty in forum The Lounge
    Replies: 1
    Last Post: 10-10-2013, 12:46 AM
  5. Wheel arches different
    By agr071 in forum The Lounge
    Replies: 6
    Last Post: 25-02-2010, 07:35 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •