Page 3 of 12 FirstFirst 12345 ... LastLast
Results 21 to 30 of 118

Thread: HQ Belmont Panelvan Rebuild

  1. #21
    P Plater hogvan's Avatar
    Join Date
    Jun 2014
    Location
    North VIC
    Posts
    74
    Quote Originally Posted by Vombil View Post
    Mate props to you! What a job. no stone un-turned there

    I know a bloke who did this conversion on an HX. It drives really really well. Total spin out going for a drive in an old panno that pulls like a commy!

    anyways that resto cost him around $150,000... outta my league :(


    Carn the Q!!!!!!!!!!!!!!!!!!!
    Yeah this hobby ain't cheap $150k definitely out of my league too! still i'd hate to add up the receipts

    - - - Updated - - -

    Front clip on





    Last edited by hogvan; 04-10-2014 at 09:41 PM.

  2. #22
    P Plater hogvan's Avatar
    Join Date
    Jun 2014
    Location
    North VIC
    Posts
    74


    Last edited by hogvan; 04-10-2014 at 09:34 PM.

  3. #23
    P Plater hogvan's Avatar
    Join Date
    Jun 2014
    Location
    North VIC
    Posts
    74






    So that's basically where i'm up to after about a years work. Should hopefully have the van running in the next couple of weeks then off to paint.
    Last edited by hogvan; 04-10-2014 at 09:39 PM.

  4. #24
    Night Rider Vombil's Avatar
    Join Date
    Feb 2011
    Location
    Western Suburbs
    Posts
    2,630
    mate thats pretty much flying along for 12 months!

    is that a rares full cowl section? did that repairs give you much trouble or take a really long time?

    should do some pretty sick skids when she's done
    BQZ

  5. #25
    Moderator Alien DNA's Avatar
    Join Date
    Jun 2010
    Location
    Melbourne, Australia
    Posts
    3,315
    Stellar effort for 12 months!!

  6. #26
    Cruiser Gunna Do's Avatar
    Join Date
    Aug 2012
    Location
    Townsville QLD
    Posts
    223
    great job ,i like your little wood stove you have in the corner to keep you warm while you work on it.

  7. #27
    Cruiser
    Join Date
    Nov 2010
    Location
    port priest south australia
    Posts
    221
    The drive line is killer what is the motor tran out of and did u have to chop the floor much? Have u put a nine inch in it?

  8. #28
    P Plater hogvan's Avatar
    Join Date
    Jun 2014
    Location
    North VIC
    Posts
    74
    Quote Originally Posted by Vombil View Post
    mate thats pretty much flying along for 12 months!

    is that a rares full cowl section? did that repairs give you much trouble or take a really long time?

    should do some pretty sick skids when she's done
    Hey Vombil, yeah it's a rares full cowl, the cowl was like swiss cheese so decided to bite the bullet and replace the lot. The hardest part was drilling out the spot welds took like 4 hours. I used sikaflex panel bond around the firewall apron area and spot welded inside the cab. Then kbs rustseal and cavity wax on the inside, hopefully last another 40 years. She should turn tyres like no tomorrow i'm hoping

    - - - Updated - - -

    Quote Originally Posted by Alien DNA View Post
    Stellar effort for 12 months!!
    Thanks

    - - - Updated - - -

    Quote Originally Posted by Gunna Do View Post
    great job ,i like your little wood stove you have in the corner to keep you warm while you work on it.
    Thanks mate, I wouldn't go out to the shed in winter without that wood fire love it.

  9. #29
    P Plater hogvan's Avatar
    Join Date
    Jun 2014
    Location
    North VIC
    Posts
    74
    Quote Originally Posted by HJRAY View Post
    The drive line is killer what is the motor tran out of and did u have to chop the floor much? Have u put a nine inch in it?
    The motor and trans came out of a side swiped 2005 vz ssz. The 4l60e went straight in with no tunnel mods but i've heard the t56 manual needs basically the tunnel from a commo transplanted. I wanted to avoid this so went with the auto. As for the diff it's only running a Salisbury at this point probly upgrade to something a bit lighter then a nine inch maybe borg warner not sure yet

  10. #30
    P Plater hogvan's Avatar
    Join Date
    Jun 2014
    Location
    North VIC
    Posts
    74
    Got the van running today
    Last edited by hogvan; 04-10-2014 at 09:29 PM.

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Similar Threads

  1. JAFT Rebuild
    By jaft in forum Replica Sandmans
    Replies: 83
    Last Post: 26-08-2017, 10:13 PM
  2. HQ belmont or something else?
    By hogvan in forum HELP... Is This a Sandman?
    Replies: 5
    Last Post: 08-06-2014, 03:35 PM
  3. 1973 HQ Belmont Windowless Panelvan - Gumtree - QLD
    By Alien DNA in forum Vehicles or Items Found for Sale
    Replies: 11
    Last Post: 02-12-2013, 07:41 AM
  4. Let the rebuild begin
    By 1BadVan in forum HZ Sandman
    Replies: 30
    Last Post: 01-09-2011, 03:14 PM
  5. 253 rebuild
    By wayne g in forum Engine
    Replies: 3
    Last Post: 03-07-2010, 12:08 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •