Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24

Thread: Brake Boosters explained

  1. #11
    P Plater cheesygrinner's Avatar
    Join Date
    Oct 2010
    Location
    Brisbane, Queensland, Australia.
    Posts
    80
    My mechanic has just been putting in a reconditioned brake booster in my WB van. He is going to take another look on Friday as he didn't have time to finish the job completely yesterday.

    When the brakes are applied via the pedal, it has the feeling of a notch in the actuation about 2/3 of the travel of the pedal.

    Any ideas to what this might be? The issue wasn't there prior to new booster fitment? Just trying to troubleshoot it.

  2. #12
    Sandman Driver RodneyHZ253's Avatar
    Join Date
    May 2010
    Location
    Parkes Central West NSW
    Posts
    718
    Quote Originally Posted by ozbox View Post
    HQ..double prong adjustable straight shaft..
    HQ..double prong non adjustable straight shaft..
    HJ..double prong non adjustable straight shaft..
    all 6 cylinder and v8 are the same interchangeable boosters in hq and hj.

    HX..HZ..bent shaft single circle mount to pedal 6 cylinder and 8 cylinder drum brake rear..
    HX..HZ..double diaphragm disc brake rear booster..

    WB..bent shaft same as hx hz but booster will not take early pbr master..
    WB STATESMAN..double diaphram for disc rear..master cylinder looks the same as wb commercial but is not interchangeable with drum rear.

    6 that i can think of..

    HQ HJ does not interchange with HX HZ and vice versa because of the pedals and the shafts..angle of push isnt right and brakes wont work properly..
    wb will interchange with HX HZ and vice versa but wb has metric brake lines to the master cylinder..

    sorry to steal your post adam but you were too slow and it was raining here so i just went and did it...
    Thanks oz your information is very helpful when sorting out replacement brake boaster for yellow van
    HZ jasmine yellow sandman van
    HZ Madeira red sandman van (now sold to bigrob)
    HX mandarin red sandman ute
    HZ malachite green sandman van
    Married to Jennie285

  3. #13
    Certifiable ozbox's Avatar
    Join Date
    Mar 2010
    Location
    newcastle
    Posts
    2,385
    no worries roddo...

  4. #14
    Sandman Driver mook's Avatar
    Join Date
    May 2010
    Posts
    744
    Quote Originally Posted by cheesygrinner View Post
    My mechanic has just been putting in a reconditioned brake booster in my WB van. He is going to take another look on Friday as he didn't have time to finish the job completely yesterday.

    When the brakes are applied via the pedal, it has the feeling of a notch in the actuation about 2/3 of the travel of the pedal.

    Any ideas to what this might be? The issue wasn't there prior to new booster fitment? Just trying to troubleshoot it.
    Sort of a side note to anyone tinkering with the WB's, as I discovered yesterday the slave cylinder fittings for the brake lines are imperial, but at the other end it's metric. So the imperial fitting will go into the metric hole but be loose and the metric fitting won't fit the imperial hole. Only a minor trap a discovered after 3 hours of swearing under the van.

  5. #15
    Sandman Driver ambientgoat's Avatar
    Join Date
    Mar 2010
    Posts
    516
    If I have a HJ van, do I need to put a HJ booster in it? Or can I install a HZ booster and matching HZ brake pedal?

  6. #16
    Hz booster HZ pedal
    Regards
    Neil & Cherone

  7. #17
    It's a rockin' Big Rob's Avatar
    Join Date
    Aug 2013
    Location
    Eurobodalla NSW South Coast
    Posts
    1,829
    Good info here... I didn't realise there were so many different ones.
    Vans.... This is the 2nd time round the block, 40 years later! talk about turning back the clock!

  8. #18
    Sandman Driver
    Join Date
    Mar 2013
    Posts
    568
    Quote Originally Posted by mook View Post
    Sort of a side note to anyone tinkering with the WB's, as I discovered yesterday the slave cylinder fittings for the brake lines are imperial, but at the other end it's metric. So the imperial fitting will go into the metric hole but be loose and the metric fitting won't fit the imperial hole. Only a minor trap a discovered after 3 hours of swearing under the van.
    Interesting subject. May I add a further side note to that, when I went to get the brake line over the rear axle re-made cause it was mangled, my local brake shop did it pretty inexpensively in new bunge, but the fittings they provided had metric flats, (This was to go on an HX).

    They reckoned they could not get fittings with imperial flats anymore, but said the thread on the fittings they supplied was the same. Anyway, whilst the thread fitted, the flats are metric. I really don't like any mix of metric and imperial on a restored car personally. so I will redo that job later. I didn't measure the thread, but it matched the new wheel cylinders and also the old ones which had fittings with imperial flats.

    Anyway iif it really is true brake shops cant get fittings with imperial flats anymore, maybe its worth saving the old fittings if they are in good nick. P.S. The recent series of Sidchrome spanners have that little notch in the open end side. I've found these heaps better for cracking those tight semi seized 20 year old fittings without distorting the flats than the previous style. (Having two notched 3/8th spanners even better.) Drop of penetrene a few hours before, and they come off like new.

  9. #19
    Banned
    Join Date
    Feb 2010
    Location
    Central West NSW
    Posts
    4,463
    Flare nut spammers are what you are meant to use for fittings like brake lines.
    You should be able to get imperial fittings.

  10. #20
    Cruiser
    Join Date
    Sep 2013
    Location
    Eastwood, NSW
    Posts
    366
    Quote Originally Posted by wbute View Post
    Flare nut spammers are what you are meant to use for fittings like brake lines.
    You should be able to get imperial fittings.
    What SLR_dave has said is 100% correct.

    AFAIK pipe nuts with a 3/8" hex have not been available for over 15-20 years, but you can still buy them with metric threads. Confusing, isn't it ? Put simply, you can still purchase a full range of pipe nuts & fittings with imperial threads, but they have metric hex sizes.

    In other words all pipe nuts with either 10mm or 3/8" threads are both manufactured from the same 10mm hex bar stock.

    Rear axle brake pipes for WB (or early Commodore) are quite unique in that they have a 3/8" UNF nut at one end to suit the imperial wheel cylinders & a 10mm x 1 metric nut at the other to fit into the junction block integral with the rear axle to chassis brake hose.

    You would need very good eyesight to be able to distinguish between a 3/8" hex & a 10mm hex without a spanner or vernier calipers. Even the most anal restorer (or concours judge) would not bother with such a minute difference. Also, a remade brake pipe utilising brand new pipe nuts looks a lot nicer than one made using old rusted or rounded nuts.

    OK, you would need to 'infect' your old Holden imperial toolkit with the occasional metric spanner but I'm sure there are other areas on a WB that require metric tools. A set of good quality flare nut spanners (both SAE & metric) is a good investment & a must for any serious restorer.

    Dr Terry
    Last edited by Dr Terry; 04-10-2015 at 11:09 AM.

Thread Information

Users Browsing this Thread

There are currently 4 users browsing this thread. (0 members and 4 guests)

Similar Threads

  1. Steering columns explained
    By ozbox in forum Ozbox's Workshop
    Replies: 75
    Last Post: 22-08-2020, 11:23 AM
  2. GV Axles explained
    By Kingcoffee in forum Driveline
    Replies: 9
    Last Post: 17-06-2013, 07:33 PM
  3. Deratings explained
    By Blocker in forum The Lounge
    Replies: 6
    Last Post: 07-11-2011, 11:34 AM
  4. Date coding explained
    By ozbox in forum Ozbox's Workshop
    Replies: 27
    Last Post: 09-10-2011, 09:14 PM
  5. Netiquette explained
    By Blocker in forum Forum Rules
    Replies: 0
    Last Post: 31-05-2010, 12:13 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •