Results 1 to 7 of 7

Thread: Extra notes on rebuilding steering columns

Threaded View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Sandman Driver
    Join Date
    Mar 2013
    Posts
    568

    Extra notes on rebuilding steering columns

    Quote Originally Posted by http://www.mysandman.com.au/forums/showthread.php/561-Steering-columns-explained[/url
    But are the column body's interchangeable?
    But are the column body's interchangeable?

    Not all of them are interchangeable, some bits are, some bits are not. The top bearing housings (houses the indicator stalk) are different, it's not just that from HX onwards they have the combination wiper/washer indicator stalk; the angle of the ignition barrel changes somewhere between HX and WB (from memory), and also some (maybe all) of the the earlier column body's will not fit properly on to the top bearing housing, (almost certainly by design). They are very close, but when you fit the parts together you can see that they don't align properly, or (for instance) you will see that the steering lock cam is going to foul the barrel, or the top four bearing housing screws do not align properly with the column. Looking carefully at the pictures that ozbox has povided, the very slight change of angle on the ignition barrel can be seen.

    A really important thing for rebuilders that can save time and money is the correct vice points for holding the columns when you dismantle and rebuild them.

    To hold the steering column in a vice so that you can disassemble it easily you remove the 4 set screws that secure it it to the dashboard mounting bracket (the piece with the three bolts that attach to under the dash), thread 2 of the set screws back into the steering column and grip these gently in the vice. Now you can work on the column without crushing it.




    This is really important as (obviously) the steering column is designed to collapse, and when rebuilding one, maintaining this safety feature is pretty key.

    Using the correct vice points will help prevent damage to the collapsible mechanisms.

    When rebuilding one from several, I'd do this with donor columns as you dismantle them for parts, even the ones you think you only need non crushable parts from, because you may decide later on that you do need to use parts from a donor column differently if the way you had it worked out if it doesnt fit. Thats how it happened for me, anyway. (They really look identical until you start matching/fitting the parts up, there's only millimetres in it).


    A couple of points which may help are that;

    The top bearing itself is not designed to be easily replaced, the Zamec casting of the top bearing housing has a lip which is bent over the bearing outer, it will probably/definately crack off if you try and change the top bearing - the idea I think was to replace the whole top bearing housing, but I dont think you can get em anymore, on top of that you need the right one to suit the column you are building.... you might be better off not trying to change the top bearing if you can get away with it.

    If you don't have/ cant get a serviceable black top bearing housing that suits, and need to sand back and repaint a different coloured one, it can be done, but because the metal is Zamec, it is notoriously difficult to paint, but it can be achieved with prepsol, and several coats, needs a bit of patience, I used wattyl rust kill gloss black (not to stop rust, but for adherence and finish, 4 coats, 24 hours drying and sanding in between).

    Of the ignition barrels available, some have a different angle on the turn of the cam (HX to WB I think) so you might want to experiment with the ones you already have so you can match it up before you shell out dollars for a new one bought on spec.

    - you cant make the non matching parts fit of course. Interestingly, I once took apart a column with damage identical to that shown in a pic on ozboxes thread, identical! On the one I saw, it was obviously the result of somebody deliberately jamming a non matching column case into the top bearing housing by cutting and bending it - most seriously uncool ! (and an identical result).

    Whilst doing all this of course you want to consider the collapse mechanism and not add anything that would foul it, and um, dont drop the steering rod on it's end (yes I have been guilty of that - it does collapse lol) - it's still not rocket science, but its getting a little closer.

    As far as I can remember the bottom mounting plate on WB is a different shape from HQ-HZ. I don't know if there is a way to interchange the parts at the bottom of the column, I am just going off memory here.
    Last edited by SLR_dave; 19-08-2013 at 02:49 AM.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Extra chassis bit on HZ
    By razsandman in forum Chassis
    Replies: 33
    Last Post: 01-07-2021, 06:56 AM
  2. Steering columns explained
    By ozbox in forum Ozbox's Workshop
    Replies: 75
    Last Post: 22-08-2020, 11:23 AM
  3. Rebuilding a Holden engine videos
    By Blocker in forum Engine
    Replies: 0
    Last Post: 25-10-2012, 11:12 AM
  4. Replies: 2
    Last Post: 17-12-2011, 09:22 PM
  5. rebuilding of a wreck..actually 2 wrecks
    By ozbox in forum Paint & Panel
    Replies: 7
    Last Post: 07-06-2010, 06:55 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •