Page 1 of 6 123 ... LastLast
Results 1 to 10 of 58

Thread: My New Project- HZ Kingswood

  1. #1
    P Plater
    Join Date
    Aug 2013
    Location
    Maryborough, QLD
    Posts
    35

    My New Project- HZ Kingswood

    G,day all.
    I'm a new member of mysandman.com
    I've decided to make a page of my progress on my project car.

    recently, I bought this



    Its a 1979 HZ Kingswood Utility

    Based on the codes
    It was a factory : 202 6 Cylinder
    M22 wide ratio 4 speed
    and bench seat (an odd combo, floor shift 4spd and bench)
    3.55 Banjo
    Jasmine yellow with buckskin interior

    It came with a set of jellybean mags and an alloy bullbar (which i don't plan on keeping)



    All of the spares that came in the back of the tub
    including chrome trims, spare guards, nose cone, interior bits etc.



    reasonably rust free tub (no holes)



    took Bullbar and grille off to get the bonnet open (bonnet cable snapped)




    Not too much rust in the floor pan
    (but someone exploded a bean in the front seat) NIGHTMARE



    Pic of interior (minus carpets)
    shows of new bench seat, bean bag shit and an aftermarket steering i wasnt too fussed on.




    Empty engine bay (with cardboard box to brush all the bean bags down the transmission hole)



    I Plan to use a 202 Blue motor and 5 spd celica box

    buckskin trim [before]



    Trim [after cleaning]


    Body was actually pretty straight
    (besides holes for tie rails n shit)




    And finally
    How it would've looked new in '79




    As stated before I plan to rebuild it with a 202 blue motor and celica 5 spd
    (i'm only on P Plates, hence no v8)

    I have a salisbury diff to put in it.
    Gonna get new brakes, new rubber n bushes and new paint
    haven't decided between jasmine yellow or cotillion white with blackouts n sandman decals ( i know I'd cope a lot of flack from purists if i took option two, but the decals look so damn awesome!)

    Anyway, i'll keep updating this page as i progress

    thanks in advance for your support and putting up with (no doubt) a million tech questions

  2. #2
    Cruiser jason.ruff's Avatar
    Join Date
    Jun 2012
    Location
    Darwin
    Posts
    416
    Good to see a young fella into the older cars. If you can get yours to look like the last photo hats off to you . Always difficult when on a short budget, but you will learn plenty.

  3. #3
    P Plater
    Join Date
    Aug 2013
    Location
    Maryborough, QLD
    Posts
    35
    Thanks mate. I love having forums like this to learn a lot more about old cars.
    Its great to have a large knowledge base to help bring these cars back to their glory

  4. #4
    P Plater
    Join Date
    Aug 2013
    Location
    Maryborough, QLD
    Posts
    35
    Bought a wiring harness today made of all NOS parts
    included: lights
    engine loom
    interior loom (guages switches)
    All for $80!

    (not bad considering this is made from NOS looms that are all separate in individual packaging)

    Also not bad considering the wreckers want $200 for the second hand loom out of a rusty, weathered wreck.

  5. #5
    Sandman Driver RodneyHZ253's Avatar
    Join Date
    May 2010
    Location
    Parkes Central West NSW
    Posts
    718
    Good luck keep us posted
    HZ jasmine yellow sandman van
    HZ Madeira red sandman van (now sold to bigrob)
    HX mandarin red sandman ute
    HZ malachite green sandman van
    Married to Jennie285

  6. #6
    Sandman Driver
    Join Date
    Sep 2011
    Location
    4350
    Posts
    526
    Good onya bloke, keep onto it and don't forget to post some pic's from time to time, good to see another survive. You will have tons of fun.

  7. #7
    Banned
    Join Date
    Feb 2010
    Location
    Central West NSW
    Posts
    4,463
    Have fun. Nothing odd about floor shift and bench seat. Lots had them. An odd combination was bucket seats, short seat separator and column shift.

  8. #8
    P Plater
    Join Date
    Aug 2013
    Location
    Maryborough, QLD
    Posts
    35
    thanks everyone. I a quick question, the dash warning light lenses on my standard Hz dash are damaged.
    it possible to by a replacement lens set, or do i have to get new cluster.

  9. #9
    Cruiser Dick61's Avatar
    Join Date
    Sep 2012
    Location
    Warragul, Vic
    Posts
    345
    You can get new lenses for the idiot light cluster from Rares for just over $20.00, look here http://www.rarespares.net.au/rarespa...oduct=9946769L for the part you need. I'd go with the Jasmine Yellow and put DY1 DY2 or DY3 stripes on it, leave it single light front and run GTS guards, that will totally confuse the purists! Great to see another youngster into the old Holdens.
    HQ Glacier White Belmont Ute
    Wanted Lanspeed accessories for Holden Grey engines, twin carb manifolds, extractors, rocker cover, 3 speed floor shift.

  10. #10
    It's a rockin' Robbo's Avatar
    Join Date
    Mar 2010
    Location
    Sunshine Coast
    Posts
    1,572
    Good on you, this will be another great Ute saved.
    "Proud To Be An Old Fart".

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. HZ Kingswood Panel van - Project
    By GNGBNG in forum Replica Sandmans
    Replies: 95
    Last Post: 01-04-2017, 12:22 AM
  2. Big Rob's HJ Ute Project
    By Big Rob in forum HJ Sandman
    Replies: 27
    Last Post: 11-05-2015, 11:45 PM
  3. Big Rob's HJ Ute Project
    By Big Rob in forum The Lounge
    Replies: 5
    Last Post: 29-04-2015, 08:02 AM
  4. Anyone up for a project or two?
    By HK1837 in forum Vehicles or Items Found for Sale
    Replies: 2
    Last Post: 14-12-2012, 03:32 PM
  5. My other Project car
    By sandman44 in forum Your Other Ride
    Replies: 8
    Last Post: 25-05-2011, 12:00 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •