Page 1 of 7 123 ... LastLast
Results 1 to 10 of 69

Thread: My HZ Sandman Panelvan Replica

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487

    My HZ Sandman Panelvan Replica

    I guess I should probably start an actual tread for the old girl...

    Here's the story so far....

    Its a HZ Kingswood Panelvan with factory 253, 4spd and 3.36:1 diff. Original paint - Persian Sand Mk II - and Tan interior.. Was factory buckets and console..

    Its fairly stripped, but its workable, and a very good base for a first van for a 19yr old!

    I'm going to build a HZ Sandman replica in Persian Sand (the van is almost a Sandman, if it was a base model - not a Kingswood - it would be one for sure..), but I'm undecided if I'll keep the factory Tan (67V) trim or go Slate Black (18V)..

    Nice straight and rust free quarters, and its windowless!!!!





    The cowels are MINT! Same as the roof, roof gutters, upper & lower tailgates, and the firewall... Haven't seen the floorpans yet, thats the first job, clean the old girl out....



    The roof is spotless, not a dint to be seen...



    This is the worst rust in the whole car:



    Its got an archway in the back, and has a stack of other parts in the back aswell... All that it set me back was $100 and a bullbar (that I got given for nothing..)
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  2. #2
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    I've had another quick look at the van, and realised that the rear window has curtains too! I dunno if I'm gonna keep them, but if I do, I'll put new ones in, cause they look really bad at the moment haha



    I also found a little more rust in the floorpans - after I filled up a 30-40L bin with leaves, dirt and sticks :/ - but its not as bad as I thought it was gonna be. and its 100 times better than my parts ute floor! haha

    Its fixable, and shouldn't be too hard to fix either, now that I can weld! haha

    Only bit in the P/S:



    The D/S is a tad worse, but its not too bad..





    I also found the metal brackets that hold the firewall lace/rubber on (painted ones..) and I cleaned polished and waxed them just to get an idea of what the colour was like originally... and my jaw hit the ground when I seen the colour when it was clean! haha
    I had a bit of trouble getting the metallic part of the paint, but its there...





    You can see the metallic/glittery bits around the glare in this picture...



    I really like the colour, up to GMH (of the 70's..) for running the colour!
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  3. #3
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    Last weekend I got her out and started to clean her up inside and out.. I had a sift through the parts in the back and sorted what was good and what was going to the tip...

    I removed about 20-30 litres of half decomposed, plant life from the cowel/plenum and to my surprise, there was not a spec of rust underneath it!

    I then turned my attention to the paint, I got the good old car wash and a sponge out, washed the old girl down and then polished and waxed one windowless section by hand.. The results were pretty good!



    The paint is pretty decent underneath with a good clean and polish..But it will still be getting a respray.



    Nice and straight, there is two dints the size of peas in one whole side of the car....

    In the below pic you can see the metallic in the paint pretty well.. It only took about 15 photo's to finally pick it up! haha



    Also found the boxes in the back of the van made out of gal and just covered in carpet.. hahah They actually had pretty good storage! and in one compartment they had a great big earth cable bolted to the floor, so they possibly had another battery in there..
    Note: the epic late 80's/early 90's speakers..



    While cleaning I found this sticker from a BnS ball in Moree 1990... I have been informed from the owner before me that the van went to the BnS ball and was pulled off the road a year later and just left to sit, so its been sitting since 1991... and it has been a country car its whole life..



    Also good news! I have found the original owner of the van!!! :D They also happened to own my parts car for the ute too.. But I've been trying to get in contact with them regarding info on the car on what happened to it to require the chassis be replaced etc.
    So fingers crossed they have the original chassis and engine sitting on their farm somewhere If not, I'd be happy just knowing a little about the vans history

    I spent $150 on stuff the stunt the growth of rust.. The plan is to wire wheel/strip any peice of rust that can be seen, rust convert, then give it a coat of paint.. and for areas I can't see, they'll be getting a fair bit of fish oil..
    By no means is it a fix, but its a preventative measure to limit the growth of the rust until I can remove it completely..

    Once again, stay tuned for progress
    Last edited by 83 WB_Ute; 28-06-2013 at 08:28 PM.
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  4. #4
    It's a rockin' Robbo's Avatar
    Join Date
    Mar 2010
    Location
    Sunshine Coast
    Posts
    1,572
    Seems to be pretty good van. All the best with your restoration.
    "Proud To Be An Old Fart".

  5. #5
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    Quote Originally Posted by Robbo View Post
    Seems to be pretty good van. All the best with your restoration.
    Cheers man
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  6. #6
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    I forgot to add... The van itself was a straight swap for parts, and the $100 was for a pair of MINT spotless, rust free doors (including door trims and all internal stuff..) So the doors made the deal even sweeter!
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  7. #7
    Moderator Alien DNA's Avatar
    Join Date
    Jun 2010
    Location
    Melbourne, Australia
    Posts
    3,315
    Must admit, thats a great colour!!

    Looking forward to updates

  8. #8
    It's a rockin'
    Join Date
    Aug 2011
    Location
    SA
    Posts
    1,067
    if you are going to paint it STOP polishing it .Great to see another van saved (who cares if its not a sandman) as for trim colour i would go for chamois trim.keep up the good work and keep it as dry as you can even if you have to spend a few hundred on a good car cover

  9. #9
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    Quote Originally Posted by Alien DNA View Post
    Must admit, thats a great colour!!

    Looking forward to updates
    Cheers mate! Hopefully updates will be consistent, but in reality, it'll be when the funds can allow :(

    Quote Originally Posted by Dick61 View Post
    I had a Persian Sand V8 HZ sedan, top car, actually if you're 19 Matt, I had my Kingswood before you were born!
    Hhaha That'd have to make you feel old! haha

    Quote Originally Posted by thatotherguy View Post
    if you are going to paint it STOP polishing it .Great to see another van saved (who cares if its not a sandman) as for trim colour i would go for chamois trim.keep up the good work and keep it as dry as you can even if you have to spend a few hundred on a good car cover
    It'll be a complete bare metal respray.. Does it matter about polishing it even if I'm going to bare metal with it?

    I agree!! I'm just happy to have a decent windowless van The interior is the only part that I am actually undecided on :/ Got some pictures of chamois trim??

    Cheers man, and fingers crossed I don't find any more rust, and hopefully I can stop the stuff I have found rusting anymore..
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  10. #10
    Cruiser Dick61's Avatar
    Join Date
    Sep 2012
    Location
    Warragul, Vic
    Posts
    345
    I had a Persian Sand V8 HZ sedan, top car, actually if you're 19 Matt, I had my Kingswood before you were born!
    HQ Glacier White Belmont Ute
    Wanted Lanspeed accessories for Holden Grey engines, twin carb manifolds, extractors, rocker cover, 3 speed floor shift.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Sandman replica
    By Jerry in forum Replica Sandmans
    Replies: 31
    Last Post: 04-03-2015, 08:53 PM
  2. My replica HQ Sandman panelvan
    By HQSandmanute in forum Replica Sandmans
    Replies: 19
    Last Post: 11-09-2013, 07:24 PM
  3. HZ Sandman Replica.
    By Robbo in forum Vehicles or Items Found for Sale
    Replies: 7
    Last Post: 12-04-2013, 02:39 PM
  4. Sandman replica
    By adam perth in forum Replica Sandmans
    Replies: 13
    Last Post: 03-09-2010, 06:52 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •