Page 4 of 6 FirstFirst ... 23456 LastLast
Results 31 to 40 of 51

Thread: 83 WB_Ute's Ultimate Shed Thread

  1. #31
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    Well, finally got around to going and picking up the parts from Queensland... We drove 1700k's (up and back..) to go and see some family, so I thought that I would tag some car parts on the end..

    This fulla was wrecking a WB that was full of rust, and I went and had a look at it. I found that it had a set of original Dragway Splats on it with decent rubber on them.
    They are 14 x 7 all round, they have 225/65's on the rear and 215/65's on the front, all the tyres would pass rego no problems at all...
    There are a few bumps on the edges of the rims, but overall they are pretty good..

    I also picked up a heater cable, the rear mudflaps and he threw in the heater controls on the dash for nothing..

    Here are some pics..

    Genuine Dragways!!





    The one on the left is after a light clean, and the others need a clean badly..







    The backs are very very dirty.. Ohh, and the 4runner in the back ground is the trusty daily run about.. It has been i our family since brand new, dad brought it from Tamworth Toyota and it has been a country car ever since.. Its the highest optioned you could get, SR5 with 5spd manual, it is a 2.8L (Sighs..) Diesel - Its absolutley gutless.. - and special velour interior.. lol But it is just going over 403,000k's on the last trip.. It is all original, only ever had 2 clutches done and 3 timing belts done since 1990..
    Once it gets to 425,000k's the engine is coming out for a freshen up and a turbo, then the gearbox will follow.. Its all in preparation for mum and dad towing the caravan.. lol

    This is the worst on one of the front wheels.. What do you guys reckon?? safe to drive on???



    Its still got heaps of tread left..

    Rears


    Fronts


    I also picked up some strips my aunty was holding.. They are WB kingswood strips, full set plus an extra door one.. They are in pretty good nick as well..





    The speedo is finished being fixed, and is ready to be collected. Hopefully I can get it soon..

    I am getting a few more parts from a wrecker to finish the main things that need to be done. Ohh, and am going to try and get the right throw-out bearing tomorrow so I can put the gearbox back in and have the clutch adjusted properly!!

    Well thats all the progress for the moment!
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  2. #32
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    Well, its definatley long time no see!!

    A lot has happened between last post and now, I have a big surprise that I will reveal later!

    I finally got my guages back from the instrument shop.. Speedo was all rebuit, except they had put washers over the trip meter stalk (behind the guage face) to hold it in place.. But not only did they hold it in place, the washers fouled on the frame of the speedo and stopped the trip meter resetting :( So I removed them! haha
    I then installed the new guage lenses..



    We also worked out where the missing wire went.. They just linked together like this..



    Then I fitted them and finally got the guages working.. It was just some corrosion on the fuse terminal :( Why the hell didn't I think of that earlier?? Then I found out by discussing with an Auto Electrician that the oil pressure sender is a faulty one.. :( So gotta fix that..
    I also wired the tacho up.. So I have a fully functioning GTS dash except for the clock and the oil pressure guage..

    I also fixed the clutch pedal problem.. I got the correct throwout bearing for it and put it in..
    Correct throwout bearing is on the right.. Wrong one is on the left...



    I also cleaned and fitted the clutch for cover..



    I thought I'd chuck in some sneak peeks of the car with the freshly polished Dragways on it!







    Then I finally got around to fitting the kingswood strips.. and took it back to 'factory' spec ready for it to pass rego (Hint Hint! ) haha









    I also finished the GTS dash fasica.. There are a few little lines that I can get rid of later on.. And I also have to paint the chrome line around the edges, but not bad for a first attempt!



    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  3. #33
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    I'm back after a little break.. I have done 6 of my 7 HSC exams and don't have the last one until the 7th of next month so I decided that I would finally finish something that I had started..

    I had started creating some kick panes for the ute to fit the 6.5'' Pioneer speakers and tweeters into. I thought long and hard about it for a while and devised a plan that would allow me to mount them up fairly high aswell as fitting into the factory recessed bump in the firewall.

    I mocked them up with cardboard to start with, I had to do this twice just because I wanted to move the speakers position so it was closer to the recessed bit..

    I then got some 6-7mm wooden board from in the shed, traced the templates on and then cut them out.. Once they were cut out I trial fitted them to the car several time to make running adjustments to make them fit better, I chiseled a few sections down so it created a spot for the factory hold spot on the firewall and to make it easier for the pinchweld to fit over the back of the new panel.





    Then I painted them black just incase if any holes happened when I covered them in vinyl.



    I then bought some black grained vinyl and trimmed them myself with it. Its not the best trim job, but it'll do for now


    (It needs a bit more work here, I fixed the bubles before I fitted them to the car..)

    I then finally fitted them to the car to replace the original plastic items. I'm quite happy with the result What do you think??







    I then turned my attention to the head unit.. I thought about it for a while and finally decided to mount it in the glovebox. I sat there staring at if for 20 minutes just playing out what I was going to do, I finally decided to mount the bracket straight to the top of the glovebox so the CD player was flush up against the to pof the glovebox..

    Another 20 minutes later and it was done! I have cut two holes in the back of the glovebox to allow the wires to go into it and I'm going to line the edges of them with pinchweld to protect the wires..

    So this is what it looks like now..





    It isn't wired up yet, but it will be soon

    Anyway, thats it for now.. Hopefully I can get some more stuff done soon
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  4. #34
    Forum Mum jennie285's Avatar
    Join Date
    Apr 2010
    Location
    Parkes Central West NSW
    Posts
    2,464
    That is a brilliant job Matt. All that and studying for HSC. I read thread from start to finish, and you have spent a lot of time sourcing correct parts, and reconditioning other, you will enjoy driving this old girl...
    HZ Jasmine Yellow Windowless Sandman, now being driven everywhere and is finished!
    HZ Madeira Red Windowless sandman now Sold to Bigrob
    HX Mandarin Red Sandman Ute finished, and club registered
    1979 HZ malachite windowless van with 308 5spd, all chromed up and shiny finished and named "The Player"
    Married to RodneyHZ253

  5. #35
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    Quote Originally Posted by jennie285 View Post
    That is a brilliant job Matt. All that and studying for HSC. I read thread from start to finish, and you have spent a lot of time sourcing correct parts, and reconditioning other, you will enjoy driving this old girl...
    Thanks Jennie I'm glad with how it has turned out, even with most of my concentration being directed to the HSC.. Sure there are a LOT of things that need improvement, but I am very picky and if it isn't good enough then I'll do it again to make sure it is the best it can be.. It is heaps better having it on the road so that I can have a car and then make improvements while driving it..

    All of this would not have been possible without the help from all the helpfull and generous members on her that have helped along the way, and for that I thank everyone

    --- Updated ---

    It never ends.. :( I just found that the drivers rear tyre is going flat and it has a leak right near the kick panel.. :( I'm pretty sure that it is coming from the tounge/metal clip that is pressed out of the firewall for the kick panel to fit behind.. :( So I'll have to fix that too..
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  6. #36
    Sandman Driver ambientgoat's Avatar
    Join Date
    Mar 2010
    Posts
    516
    Nice one, those look neat.
    The only suggestion I'd make it trying to get those tweeters up near ear level somewhere. The high frequency sound is very directional, so unless your ears are in your shins they're probably being wasted down there.
    As I said tho, looks nice, suspect I'll be copying what you've done for my van in a couple weeks.

  7. #37
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    Quote Originally Posted by ambientgoat View Post
    Nice one, those look neat.
    The only suggestion I'd make it trying to get those tweeters up near ear level somewhere. The high frequency sound is very directional, so unless your ears are in your shins they're probably being wasted down there.
    As I said tho, looks nice, suspect I'll be copying what you've done for my van in a couple weeks.
    Thanks mate.. Yeah, I was going to try that straight up, but thought I'd go for something a bit easier... I will have a set of four inch speakers a little higher up in the b-pillar and then some 6'' x 9'' down low behind the seats I will probably re-route the tweeters at some stage though..

    Hahaha Glad I could inspire you to want to copy me! hahaha Let me know if you need a hand with measurements etc..
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  8. #38
    It's a rockin' Robbo's Avatar
    Join Date
    Mar 2010
    Location
    Sunshine Coast
    Posts
    1,572
    You have done a great job with your ute, I am sure you will really enjoy driving it. Nothing like pride of ownership, and you have done all the work yourself.
    "Proud To Be An Old Fart".

  9. #39
    Sandman Driver 83 WB_Ute's Avatar
    Join Date
    Sep 2011
    Location
    Northern NSW
    Posts
    487
    Quote Originally Posted by Robbo View Post
    You have done a great job with your ute, I am sure you will really enjoy driving it. Nothing like pride of ownership, and you have done all the work yourself.
    Thanks mate.. It is really good to drive, alot better than I expected.. It is good to know that if something does break that I can fix it there and then on the side of the road..
    Cheers,
    Matt

    My WB Ute Build:
    http://www.mysandman.com.au/forums/s...te-Shed-Thread

    My HZ Sandman Panelvan Replica:
    http://www.mysandman.com.au/forums/s...nelvan-Replica


    WHERE ARE YOU BHZ29069A!?!?!?

  10. #40
    Not sure weather I like the standard wheel with caps better or the Dragways....

    One thing I think would look really good is if you lost about a foot suspension all around.

    Good luck with it buddy! Hope you have plenty of cruisin time in her!

    Cheers Jon
    Last edited by SMQQTH; 25-01-2013 at 09:18 PM.
    Owner of one 2004 VY 'Holden By design' Sandman!

    No I don't need a sticker package to tell me what I drive!

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Similar Threads

  1. Ultimate Car Porn Thread
    By Alien DNA in forum Car Pics
    Replies: 46
    Last Post: 02-04-2013, 05:05 PM
  2. Jeff76 Shed Thread
    By jeff76 in forum HX Sandman
    Replies: 0
    Last Post: 17-09-2012, 04:35 AM
  3. fitzie's Shed Thread
    By fitzie in forum HX Sandman
    Replies: 0
    Last Post: 17-09-2012, 12:35 AM
  4. Scotty77 - Shed Thread
    By Scotty77 in forum HX Sandman
    Replies: 3
    Last Post: 18-04-2012, 12:35 AM
  5. V6HQUte - Shed Thread
    By V6HQUTE in forum Replica Sandmans
    Replies: 12
    Last Post: 28-12-2011, 12:35 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •