Page 2 of 2 FirstFirst 12
Results 11 to 14 of 14

Thread: Help!!!! WB Seat Identification

  1. #11
    Sandman Guru
    Join Date
    Jul 2010
    Posts
    6,451
    When you put Commodore (VB-VL) seats into HQ-HZ only 1 seat bolt aligns (front one closest to sill). You have to drill a hole for the other front bolt right next to the other side captive floor nut (by right next to I mean it is that close that you don't need a spanner on the nut you put in as its flat will be hard up against the existing captive nut). If you use an original captive nut that you have chiselled off a rusty donor floor and sit it next to the existing one it will look factory, and the hole is drilled through the floor and the underfloor member. The problem arises with the back 2 bolts: holes go through single skin un-reinforced steel.

    With WB seats (or Commodore seats with WB rails) bolts on one runner align with existing captive floor nuts (outmost - closest to sills). You do the same for the front other side as per Commodore seats. And then the rear other side is done the same as the front. You end up with holes through where it should be (through the floor and an underbody member). What I have done is simply tack weld the new nuts to the existing captive nuts. Looks factory once done. Looks even better if you grind off the inner original captive nuts, drill a hole in the required place and weld in a donor captive nut in the right place. Just put some black goop in the original holes. Then your HQ-HZ floor is basically as per WB.

    If I get time i'll put up a photo of WB runners next to VB-VL runners. You'll see they are the same thing, just WB have extra outriggers spot welded to the Commodore runners to pick up the WB floor holes.

  2. #12
    Cruiser Mazdragon's Avatar
    Join Date
    Jun 2010
    Location
    Melbourne
    Posts
    258
    Now i'm a little worried, i have a WB with bench seat. Have purchased and refurbed a set of HZ Wagon buckets I was told would bolt straight in... i fear this may not be correct? Just going by what I have read so far on this thread.... any good advice appreciated... thanx Maz
    it's here and I love it!!

  3. #13
    Sandman Guru
    Join Date
    Jul 2010
    Posts
    6,451
    The outermost holes/nuts are in the same spot on all HQ-WB (so the HZ bench fits WB). The innermost holes/nuts (closest to tunnel) are further away from the tunnel on WB by about 20mm or so than they are on HQ-WB. Hence HQ-HZ seats won't simply bolt into WB (and vice versa).

  4. #14
    Cruiser Mazdragon's Avatar
    Join Date
    Jun 2010
    Location
    Melbourne
    Posts
    258
    so drill holes to suit and fill the ones that are left "spare"? doesn't sound too hard. But thanks for lettg me know, at least i can be prepared now.
    it's here and I love it!!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Gts rim identification
    By ozbox in forum Ozbox's Workshop
    Replies: 7
    Last Post: 23-10-2011, 01:43 PM
  2. HZ Panelvan Identification
    By Rokvan in forum HELP... Is This a Sandman?
    Replies: 2
    Last Post: 23-05-2011, 03:46 PM
  3. Give Away. HZ bench seat + HQ bench seat.
    By razsandman in forum Archive
    Replies: 1
    Last Post: 30-12-2010, 01:31 PM
  4. hj van identification
    By kaido17 in forum The Lounge
    Replies: 1
    Last Post: 01-10-2010, 11:04 PM
  5. Identification corrections
    By Blocker in forum Holden Sandman Q&A
    Replies: 14
    Last Post: 01-03-2010, 07:07 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •