Results 1 to 9 of 9

Thread: Casting sand in new intake Manifold

  1. #1
    Forum Mum jennie285's Avatar
    Join Date
    Apr 2010
    Location
    Parkes Central West NSW
    Posts
    2,464

    Casting sand in new intake Manifold

    Inside new KC intake manifold, mostly in the top, and difficult to see because it had been sprayed over with silver paint, casting sand found.

    I would imagine this casting sand woud destroy a motor in no time at all, we hope ours has not been hurt in any way.











    HZ Jasmine Yellow Windowless Sandman, now being driven everywhere and is finished!
    HZ Madeira Red Windowless sandman now Sold to Bigrob
    HX Mandarin Red Sandman Ute finished, and club registered
    1979 HZ malachite windowless van with 308 5spd, all chromed up and shiny finished and named "The Player"
    Married to RodneyHZ253

  2. #2
    It's a rockin' playwme's Avatar
    Join Date
    Apr 2010
    Posts
    1,935
    Wouldn't think it would be enough to destroy a motor but it wouldn't be good for it. Is it solid clumps or does it crumble really easy?

    Did they find that at the Dyno tune?

  3. #3
    Forum Mum jennie285's Avatar
    Join Date
    Apr 2010
    Location
    Parkes Central West NSW
    Posts
    2,464
    Yes Rodney and the dynotune guy, and Adam (our panelbeater) found it before they put the carby back on, just felt up in the inlet manifold to check studs didn't come through into the manifold void, and found this silver paint on fingers, then rubbed a little harder then became aware of the sand, there was various lumps of sand lodged in about 5 places.....:knockout:
    HZ Jasmine Yellow Windowless Sandman, now being driven everywhere and is finished!
    HZ Madeira Red Windowless sandman now Sold to Bigrob
    HX Mandarin Red Sandman Ute finished, and club registered
    1979 HZ malachite windowless van with 308 5spd, all chromed up and shiny finished and named "The Player"
    Married to RodneyHZ253

  4. #4
    Leadfoot skid's Avatar
    Join Date
    Jun 2010
    Location
    Brisbane
    Posts
    122
    Fingers crossed for you that the engine is ok.
    we know how much time and effort has been put into that van.
    cheers :lifesaver::lifesaver:
    HX XX7 windowless Van needing resto
    WB ute

  5. #5
    Decal Demon stickthis's Avatar
    Join Date
    Feb 2010
    Location
    SA
    Posts
    1,957
    Will be interesting to see what "KC" say about this. Not good enogh for the intake of an engine. Just leave your air cleaner off Jenny will do the same thing...... I would be making a very big point of it to the supplier. Also getting someone with a camera to check out the bores though the spark blug holes for any scuffing.
    Owner (Jason) - STICKTHIS Automotive Decals and Stripes

    HX Sandman Panelvan. Mint Julep. Complete Factory Resto.
    HZ Sandman Ute. Saddle Tan Metallic - Customised. Galaxy Blue.
    HZ GTS. Palais White. Next Resto From 99% NOS Parts.
    HSV GTO Coupe - Highly Modified
    VR SS into a VS Supercar Castrol Perkins Ingall 1997 Tribuilte build

  6. #6
    Forum Mum jennie285's Avatar
    Join Date
    Apr 2010
    Location
    Parkes Central West NSW
    Posts
    2,464
    Quote Originally Posted by stickthis View Post
    I would be making a very big point of it to the supplier. Also getting someone with a camera to check out the bores though the spark blug holes for any scuffing.
    We spoke to our engine builder this morning, he has never heard of this happening before, and he will checking for scuffing when we go over to him. Rodney has left for dubbo to try and get it all back together again, they cleaned out the sand last night....
    HZ Jasmine Yellow Windowless Sandman, now being driven everywhere and is finished!
    HZ Madeira Red Windowless sandman now Sold to Bigrob
    HX Mandarin Red Sandman Ute finished, and club registered
    1979 HZ malachite windowless van with 308 5spd, all chromed up and shiny finished and named "The Player"
    Married to RodneyHZ253

  7. #7
    Decal Demon stickthis's Avatar
    Join Date
    Feb 2010
    Location
    SA
    Posts
    1,957
    ah very good. Good of him to help out. Hardly the builders fault.
    Owner (Jason) - STICKTHIS Automotive Decals and Stripes

    HX Sandman Panelvan. Mint Julep. Complete Factory Resto.
    HZ Sandman Ute. Saddle Tan Metallic - Customised. Galaxy Blue.
    HZ GTS. Palais White. Next Resto From 99% NOS Parts.
    HSV GTO Coupe - Highly Modified
    VR SS into a VS Supercar Castrol Perkins Ingall 1997 Tribuilte build

  8. #8
    Banned
    Join Date
    Feb 2010
    Location
    Central West NSW
    Posts
    4,463
    How dissapointing! Tim would have looked in about 3 million of those, had he ever seen that before?
    Edelebrock may be the go instead of KC?

  9. #9
    Forum Mum jennie285's Avatar
    Join Date
    Apr 2010
    Location
    Parkes Central West NSW
    Posts
    2,464
    Tim nearly fell over, he was so disgusted in the way things are being built..He has not seen that before and Rodney is still over there trying to get it all back together, they have worked on it all weekend....he did say Edelbrock would have been better....very lucky it didn't get into the motor (we hope):Chin:
    HZ Jasmine Yellow Windowless Sandman, now being driven everywhere and is finished!
    HZ Madeira Red Windowless sandman now Sold to Bigrob
    HX Mandarin Red Sandman Ute finished, and club registered
    1979 HZ malachite windowless van with 308 5spd, all chromed up and shiny finished and named "The Player"
    Married to RodneyHZ253

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. sand man van
    By rocky in forum The Lounge
    Replies: 1
    Last Post: 26-05-2015, 09:11 PM
  2. Is casting date wrong
    By Kingsandman in forum The Lounge
    Replies: 2
    Last Post: 18-09-2014, 08:13 PM
  3. AFR Composite plastic intake manifold
    By Alien DNA in forum The Lounge
    Replies: 3
    Last Post: 27-03-2014, 12:01 AM
  4. HX Sand man Ute?
    By cass in forum HELP... Is This a Sandman?
    Replies: 5
    Last Post: 15-08-2013, 02:07 PM
  5. intake manifold and carbies
    By HJRAY in forum My Items For Sale or Buy
    Replies: 33
    Last Post: 29-07-2013, 01:47 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •